When looking at the installation of any Hybrid or Electric racing car, the bright orange cabling is a trademark feature, taking the high currents between the battery, inverter and eMotor. With light weight, reliability and rapid disassembly all factors in the cabling installation, the cable choice and the connector technology are critical and often unappreciated by the fans. I’ve recently purchased some Ex-F1 DC connectors\cables which give us some appreciation of the tech involved here. These are both Red Bull RB8 (2012) parts, taken from the DC (battery to inverter) bus. Rather than simply being big fat copper cables with two pin connectors, they are remarkably complex in their design.
During the F1 KERS era (2009-2013), Red Bull Racing adopted a unique battery set up. Rather than in a recess under the monocoque\fuel tank, the battery is split up into three separate units around the gearbox. I’ve explained the KERS installation in previous posts (LINK), but I’ve recently acquired a 3D printed mockup of one of the side mounted battery cases. This gives us some unique insight into the battery case’s dimensions and layout.
With far reaching regulation changes coming onto the sport in 2014, the 2013 season is likely to be a year of consolidation, as few changes have been are written into this year’s rule book. So teams will be expected to optimise their designs from last year, correcting mistakes and adopting some of the better ideas of their rivals.
Some rules will have a small effect of car design and some trends from last year will be more common place. Unusually there have been few leaks or well-founded rumours circulating in the off season. This is probably as teams are expending a huge amount of resources in finding big gains for just one year’s competition, instead focussing on plans for 2014.
KERS has been in F1 since 2009, the system recovers energy under braking and allows the driver a boost in engine power each lap. However the FIA imposed strict limits on the amount of energy that can be recovered and discharged each lap. Which has often raised the question how do they control this usage and ensure teams are sticking to the rules? This sensor from Isabellenhütte Heusler has been introduced by the FIA this year to ensure exactly this.
As the first real launch of a 2012 F1 car, McLaren have unveiled their MP4-27. In McLaren parlance this was the cars “technical launch” and was carried out at their Technical Centre in Woking, UK.
McLaren had one of the fastest cars in 2011, on its day the MP4-26 was faster than the Red Bull. So the basic approach of the new car did not need to veer too far from direction McLaren had been following. Last year the season was blighted by poor form in pre season testing. Most of the winter tests were interrupted by exhaust problems, as the now near mythical “octopus” exhaust broke after a few laps out on track. This exhaust turned out to be far simpler than the rumours suggested. The exhausts ran sideways across the floor to exit in a longitudinal slit ahead of the rear wheels. This being a complex way to achieve the same sort of fluid skirt that Red Bull achieved with their outer blowing exhaust layout. Once McLaren had followed Red Bulls lead with the exhaust, they were able to catch up. McLaren perhaps even surpassed Red Bull with the exhaust blown diffuser, as the Mercedes Hot Blown engine mappings were superior to the Renault cold blown solutions. Despite the rules trying cap the hot blown benefits as early the Canadian GP, the Silverstone GP weekend showed how much McLaren were lost relative to Red Bull when the restrictions really bit hard.
With a strong car at the end of 2011, the team have learnt about the damage a slow start to the year makes to their championship chances. This year evolution is required, McLaren do not need to find large chunks of time, but do need a car that will perform well at the opening races. Thus we see the refinement of old concepts and little in the way of radical development.
Thus the new car bred from the recent line of McLarens, the family resemblance goes further than the colour scheme. With a low nose and sweeping lines over rounded sidepods are now trademarks of the Woking design team. With the second year of the fixed weight distribution and Pirelli tyres, little needed to be done to the cars basic layout. Running much the same chassis, fuel tank size and gearbox, so the wheelbase is similar to the previous car.
Although the 2012 Pirelli front tyres are a new shape tyre, Paul Hembury from the tyre supplier confirmed to me that the change in the new profile is “not visible to the eye”. So only small optimisations of the front end aero are needed to cope with the change.
The studio photos of the car in side profile show off the amount of rake the car is designed to run. This is also a carry over from 2011, as the car could often be seen with a clear 10cm of ride height at the rear axle line. Although managing rake will be harder this year as the greater rear height introduces more leakage into the diffuser from the sides. As yet the teams solution to seal the diffuser are hidden by a simple floor fitted to the launch, although these are removable panels and more complex designs will soon be seen.
With so much to carry over in philosophy and design, what has changed for 2012?
MP4-27 in detail
The stand out points on the MP4-27 are the nose, sidepods and exhaust position.
Firstly the front wing is near identical to the late 2011 wing, so we can expect its general design to carry over, as will the snow plough vane below the nosecone. But the height of the nose at first appears to be at odds with the 2012 rules on a maximum 55cm height for the front of the nose.
Looking closer at McLarens chassis in side profile its clear the family history of low noses has helped here. The dashboard bulkhead is may be just 3cm higher than the cockpit padding (which is 55cm high), the chassis top then curves downwards towards the front wheels. By the point of the front (A-A) bulkhead the top is lower than 55cm, may be as low as 5cm below the maximum height. When compared to the maximum heights (the dotted line on the drawing), its clear this is a very low nose overall.
This creates less space under the raised nose, but the teams snow plough device under the nose works aggressively as a turning vane, so perhaps the team don’t need the higher chassis to get the correct airflow to the sidepods leading edge. McLaren also find the lower nose provides the classic vehicle dynamics benefits of a low CofG and a less extreme front suspension geometry. This trade off works for McLaren and goes to prove not everything in F1 has to be a compromise in search of aero advantage.
Although details around the front end will change, the wheels are typically a design chosen to last for the whole season. This year the McLaren Enkei wheels sport a novel set of drillings to aid brake cooling. The usual spokes formed into the wheel between the hub and the rim, stop short and a radial set of holes are made near the rim. Although not present of the launch car, there will be a dish shaped fairing added to small pegs formed into the wheel to aid the airflow out of the wheel.
In 2011 McLaren were not afraid to try a radical sidepod set up, This was the “U” shaped sidepod, with the angled inlet shape creating channel in the upper section of sidepod (About the MP4-26 “U” shaped sidepods). This year the team have adopted more typical sidepod format, with highwide sidepod inlets and steep undercut beneath. I got to ask Tim Goss about this:
ScarbsF1: Can you tell us about why the concept’s changed, why you don’t feel that was a benefit this year?
Tim Goss: Last year’s U-shaped side-pod worked very well with what we were trying to achieve last year with the exhaust layout, it was all intended at creating more down wash to the rear end, and it performed particularly well last year. This year at a fairly early stage we set about a different approach to both the external and the internal aerodynamics of the car, and then once the exhaust regulations started to become a little bit clearer then it was quite obvious to us that the U-shaped side-pod no longer fitted in with both the internal aerodynamics and some of the external aerodynamics that we pursued early on. So it works, it worked very well last year, but it’s actually just not suited to what we’re trying to achieve this year.”
In frontal profile the high and wide cooling inlet is obvious. The team have been able to incline the sidepod tops slightly, this isnt quite a “U”pod shape, but is quite distinctive. At the rear the team have kept the sidepods narrow and slimmed the coke bottle shape in tightly to make the sidepod join the gearbox fairing creating a continuous line of bodywork to the very tail of the car.
As well as the external airflow considerations, McLaren looked the sidepods internal airflow, they wanted a cooling exit on the cars centreline. This would have been compromised with the “U” sidepod, so the more conventional shape was selected. The cooling arrangement is similar to Red Bulls philosophy, the radiators direct their heated airflow upwards and around the engine, this then exits in a tail funnel. The launch car had quite a modest central outlet, but we can expect to see far larger versions used at hot races.
Aiding the tail funnel there are also cooling panels on the upper leading edge of the sidepod, either side of the cockpit padding and various panels arund the rear of the coke bottle shape. Different panels will be used depending the cooling andor drag demands of the of the track.
Other cooling functions are covered by the inlet below the roll hoop. Last years double inlet set up has gone and now a single duct is used. This probably cools both the gearbox and KERS.
The other notable aspect of the sidepods are the exhaust bulges. These stick out prominently on the flank of each sidepod. They don’t serve an aerodynamic function themselves, but simply fair-in the final 10cm of exhaust pipe. This final section of exhaust is now strictly controlled by the regulations. Its position must sit within specific area, it must point upwards between 10 – 30 degrees and can point sideways plus or minus ten degrees. McLaren have fixed the exhaust in the lowest most rearwards position possible, the tail pipe then pointing steeply upwards and inwards. From the limited view it would appear to direct the exhaust plume towards the outer span of the rear wing.
This would make a blown rear wing (BRW), the added flow from the exhaust aiding the wing in creating downforce at lower speeds. The exhaust position and fairing also suggests an alternative exhaust tailpipe could be used. Paddy Lowe confirmed that different solutions would be tried in testing. From overhead its clear to see the exhaust could be angled differently to blow over the rear brake ducts fairings to create downforce directly at the wheel.
The gearbox case design is not the shrunken design we saw with Williams in 2011 , the differential is low but not unduly so. The top of the case sitting neatly under the tail funnel. Pull rod suspension remains at the rear of the car, while conventional pushrod is on the front end. Lowe commented that the Lotus brake antidive system was not specifically looked at, but was part ”of a family of solutions” that has been looked at in the past. The engineers feeling that the Lotus system was illegal and hence had not been explored further. They declined to comment of the possibility of an interlinked suspension system.
Behind the gearcase, the rear impact structure is mounted midway between the beam wing and floor, fully exposing both the beam wing and allowing airflow into the central boat tail shape of the diffuser. As the diffuser was covered up, its not clear if there are features to drive airflow into the starter motor hole. A new feature on the beam wing is an upswept centre section, the extra angle of attack in the middle 15cm of the wing having a slot to help keep the airflow attached. The upper rear wing is a new design albeit similar the short chord DRS flap wing, we saw introduced at Suzuka last year. The DRS pod is still mounted atop the rear main plane and its hydraulics fed to it through the rear wing endplates. The flaps junction with the endplates follows recent McLaren practice with a complex set of vents aimed at reducing drag inducing wing tip vortices.
Not much else in terms of structures or mechanical parts were evident at the launch. Lowe did confirm to me that the Mercedes AMG KERS remained packaged under the fuel tank in one assembly. Also adding that there would not be an significant weight loss to the system. As a significant reduction in weight was made between the 2009 and 2011 season, via the consolidation of the Batteries and Power Electronics into one unit.
Mp3 of the MP4-27 Engine fire up via McLaren
One of Max Mosley’s lasting legacies in F1 was the introduction of his vision of a green initiative in F1. As a result KERS (Kinetic Energy Recovery System) was introduced 2009, as part of a greater package of rule changes to change the face of F1.
KERS is a system which harvests energy under braking and stores it to provide the driver with an extra power boost each lap. A simple technical summary of KERS is here (http://scarbsf1.wordpress.com/2010/10/20/kers-anatomy/ ).
During the 2009 season McLaren were applauded for running Mercedes KERS at every race and it was widely reported as the best KERS in use that year. Along with a few other journalists, I was invited along to Mercedes AMG Powertrains in Brixworth, UK to hear about KERS development since 2009. With Managing Director Thomas Fuhr and Engineering Director Andy Cowell giving a presentation on the range of work Mercedes AMG does with its F1 teams.
Mercedes AMG Powertrains reside on the site that was previously Mercedes Benz High Performance Engines (MBHPE). Now renamed to reflect the wider application of the groups knowledge, both to uses outside F1 and to areas other than engines. Powertrain is a catch all term covering; engine, transmission, electronics and of course KERS Hybrid systems.
The company have built a purpose designed Technology Centre on the site, which historically was the Ilmor engine plant and positioned just a few miles from Cosworth in Northampton. Clearly this area has a rich seam of Engine knowledge.
Formed around three buildings the entire F1 engine and KERS development is carried out on site, only specialist functions such as the casting of the crankcases is carried out off site. Additionally other Mercedes AMG work is carried out here, such as the AMG E-cell car.
Mercedes AMG (MBHPE as it was known then) developed their first KERS for 2009 in house. At the time McLaren were the primary customer for the system, although Force India and at the last minute Brawn GP were also customer teams that year. Force India had a chassis prepared to run KERS, but chose not to during the season. Brawn had a chassis designed before their switch to Mercedes engines, so their car was not designed to accept the Mercedes KERS.
In designing the system, Mercedes AMG had a specific requirement from McLaren. As the effectiveness of KERS was unknown, McLaren didn’t want to compromise the car if KERS was removed. So the system was packaged to fit into a largely conventional car. Whereas other KERS suppliers went for a battery position under the fuel tank, McLaren and Mercedes AMG placed theirs in the right hand sidepod. Low down and far forward, on the floor between the radiator and the side impact structures. The battery pack contains not only the array of individual cells, but also the pump and pipe work for its water cooling circuit. As well as the electronic interfaces for its control and monitoring. The assembly is around 7cm high, 12cm wide and 40cm long. The KBP is probably the single heaviest KERS component. In 2009 this sidepod package was acceptable as the teams were still on Bridgestone tyres and seeking an extremely forward weight distribution. Thus the 5cm higher mounting in the sidepod was offset by its forward placement.
Conversely the smaller Power Control Unit (PCU) was placed in a similar location in the other sidepod, ironically the PCU is around the size and shape of road car battery. This left the monocoque uncompromised, aside from the smaller cut out for the MGU in the rear bulkhead.
Then the Motor Generator Unit (MGU) is mounted to the front of the engine. This device generates and creates the power for the KERS. Its driven from a small set of gears mounted to the front of the crankshaft. the unit remains with the engien when the car is dismantled and is oil cooled along with the engine.
All of the components are linked both to the SECUs CAN bus and to each other by High Current Cable. The latter taking the DC current between the Batteries and MGU. With this packaging Mercedes AMG quotes the total system weight as 27kg.
Designed and developed by Mercedes AMG, but other partners were involved; the unique battery cells were supplied via A123 and the MGU was partnered with Zytek. Although the power control electronics were solely a Mercedes AMG in house development.
Through the 2009 season both McLaren drivers had a safe and reliable KERS at each race. The system was safe even after crashes and was fault free despite rain soaked races. Safety was designed in from the outset, all electrics were double insulated. Teams can also measure damage to the unit via accelerometers and insulation sensors, so any impact or incidental damage can be monitored and the car retired if the need arises. Additionally each cell in the battery has its temperature monitored. KERS batteries are sensitive to high and low temperatures, each cell needing to operate in a specific thermal window. Too low and the unit is inefficient and too hot and there’s the danger of explosion.
Perhaps the only criticism was the sidepod battery mounting, despite several incidents, this never put any one in danger, so this never proved to be an unsafe installation.
For a variety of non technical reasons KERS was agreed not to be raced from 2010 until the planned 2013 rules. However this plan changed, but not before Mercedes AMG had made new strategic plans around KERS.
Mercedes AMG set out a longer term strategy to work on research for KERS in preparation for 2013, as well as working with AMG to develop the road car based E-cell technology.
(Link Mercedes AMG E-Cell chassis )
This changed when the plans for the 2013 engine were pushed back to 2014 and KERS was agreed to be reintroduced for 2011. Thus the 2013 development plans had to rebased and deliver a refined version of the 2009 KERS for 2011. Moreover there were now three teams to be supplied with KERS. There was no Christmas for Mercedes AMG staff 2010!
As a result of the research work carried out after 2009, Mercedes AMG now solely design, develop and produce the entire KERS package, aside from the Battery cells. So now the MGU is a wholly Mercedes AMG part.
With KERS effectiveness proven in 2009, it was possible to have the cars designed around it, rather than it be an optional fitment. So the packaging was revised and the entire system integrated into just two units. The MGU remains attached to the front of the engine, still driven off a spur gear on the nose of the crankshaft. While the KBP and PCU are now integrated into a much smaller single package and fitted under the fuel tank. The unit bolts up inside a moulded recess under the monocoque, the unit being attached using four vibration mounts, and then a closing panel and the cars floorplank are fitted under it.
It’s this integration of the batteries and power electronics that has has really slimmed the 2011 system down. Mercedes AMG now quote 24kg the entire KERS, much of the 3kg weight loss being down to the reduction in the heavy power cabling between these units.
Not only is the packaging better, but the systems life and efficiency is too. Round trip efficiency stands at a stated 80%, which is the amount of power reapplied to the engine via the MGU after it has been harvested and stored. Improvements in efficiency being in both the charge and discharge phases.
Battery pack life was extended to as much as 10,000km, several times the 2009 predictions that batteries would need replacing every two races (2,400km). Over this period, the cells do not tend to degrade, as the team manage the unit’s condition (‘State of Charge’ & temperature) throughout the GP weekend to maintain their operational efficiency.
The 80hp boost KERS provides, stresses the engine. This was well known back in 2009, but for 2011 along with DRS the car can be several hundred revs higher than the usual EOS (end of straight) revs. Mercedes AMG quoted 15-25% more stress for a KERS and DRS aided lap, this needing to be taken into account when the team monitor the engines duty cycle, thus deciding when to replace it. Mercedes conducted additional dyno development of the engine being kept on the rev limiter to fully understand and counter this problem. This work paid benefits; Hamilton ran many laps at Monza bouncing off the rev limiter along the main straight, while chasing Vettel.
KERS in use
Although the max 60KW (~80hp) output can be reduced from the steering wheel, its normal for the driver to use the full 80hp boost each time they engage the KERS boost. With a reliable KERS, the driver will use the full 6s boost on every lap. Media reports suggest Red Bulls iteration of the Renault KERS does not use this full 60kw. Instead something like 44kw, providing less of a boost, but allowing smaller batteries to be used. The loss in boost being offset by the overall benefit in car packaging.
The driver engages a KERS boost either via a paddle or button on the steering wheel, or by the throttle pedal. The latter idea being a 2009 BMW Sauber development, where the driver pushes the pedal beyond its usual maximum travel to engage KERS. Nick Heidfeld brought this idea to Renault in 2011 and the over-extended pedal idea has also been used for DRS too.
Once the driver is no longer traction limited out of a turn, they can engage KERS. Usually a few small 1-2s boosts out of critical turns provides the ideal lap time. It’s the driver who has to control the duration of the boost, by whichever control. As with gear shift the drivers can be uncannily accurate in their apportioning of the boost around the lap. It’s suggested that the 2009 Ferrari system apportioned the duration of the KERS boost via a GPS map, the driver simply presses the button and the electronics gives them the predetermined amount of boost. This solution came as surprise to Andy Cowell, so one wonders if this is legal or perhaps if the report is true.
From on board shots, we’ve seen the steering wheel has an array of LEDs or numerical displays to show the driver the boost remaining for that lap. The SECU will have control code written to prevent overuse of KERS around a lap.
Typically the battery will hold more charge than a laps worth of harvestingdischarge. So that any unexpected incidents do not leave the driver without their 6s of boost.
In use KERS can be used in several different ways. When lapping alone KERS typically gains 0.45s per lap, although this varies slightly by track. Along with DRS is can boost top speed by 12kmh. As explained the driver uses a pre-agreed amount of boost, decided from simulation work done at the factory before the race. So the planned strategy of KERS usage will be used in practice, qualifying and in parts of the race. However in the race the driver can use KERS tactically to gain an advantage. Drivers are able to use more a KERS boost to either overtake or defend a position. One feature of 2011 along with the Pirelli tyres being in different condition during the race, was the driver’s freedom to alter their racing line and use their grip and KERS to tackle their rivals.
KERS continues in its current guise for another two years, then for 2014 along with all new engine regulations there will be a new format KERS. Energy recovery will be from different sources, so the overriding term for the hybrid technology on the car will simply be ERS (Energy Recovery Systems). However KERS will still exist, harvesting energy from braking, but will have a greater allowance for energy stored and reapplied. But, there will also be TERS (Thermal Energy Recovery), which a MGU harvesting energy from the turbocharger. Overall ERS will provide a third of the engines power for some 30s of the lap. No longer will the driver press a button for their KERS boost, it will be integrated in their demand for power from the throttle pedal. The electronics will be constantly managing the Powertrains energy, harvesting and applying energy based on whether the driver is on or off the throttle. In 2014 Powertrains and ERS is set to become very complicated.
When Red Bull Racing launched their new car for 2011, the event was marked by a very special press pack. The pack was formatted in the style of the well-known Haynes maintenance manuals (PDF). This in itself this was a great book, but almost unnoticed within its pages was the intended publishing of a complete Haynes style workshop manual on the RB6 car.
Now some six months later the Haynes Red Bull Racing F1 Car Owners Workshop Manual (RB6 2010) has been published. As its rare a Technical F1 book is published, not least one with insight into such a current car, I’ve decided to review the book in detail.
At 180 pages long the book has enough space to cover quite a wide range of topics and it does so. Starting with a background to the team, moving on to the cars technology, to overviews of its design and operation. With its familiar graphical style and hardback format it certainly gives the feel of a proper workshop manual. However this is somewhat skin deep and the pages within, soon revert to a more typical book on F1, although some flashes of the Haynes style do remain.
Steve Rendle is credited as the writer of the book and Red Bull Racing themselves have allowed close up photography of the car and its parts, as well as providing a lot of CAD images.
But clearly a lot of editing has been carried out by Red Bull Racing and the book falls short of its presentation as a manual for the RB6. Despite its confusing title, the book is probably better described as a summary of contemporary F1 technology from the past 3 years.
As the last in depth technical F1 book was the heavy weight title from Peter Wright showcasing Ferraris F1 technology from 2000, this remains a useful source of recent F1 technology.
This places the books target audience, somewhere between the complete novice and those already of a more technical mindset.
With forewords by Christian Horner and Adrian Newey, the opening 21 pages are a background to the team and detail of the 2010 season that brought RBR the championships. Then starts the core 100 page chapter on the cars anatomy, which opens with a pseudo cutaway of the car showing a CAD rendering of its internals.
Firstly the monocoques design and manufacture is covered, with images of the tubs moulds being laid up and CAD images of the RB4 (2008) chassis and its fuel tank location. Although little is made of the fuel tank design.
Moving on to aerodynamics, the text takes a simplistic approach to explaining aero, but there is an interesting illustration of the cars downforce distribution front to rear. This does highlight the downforce created by the wings and diffuser, but also the kick in downforce at the leading edge of the floor, but this is not adequately explained in the text. Mention is made of the front wing and the flexing that RBR deny, this is explained with a simple illustration showing the deflection test. The driver adjustable front flap, which was legal during 2009-2010 seasons, is explained, in particular that the wing was hydraulically actuated. When I understood that in 2009, only Toyota used a hydraulic mechanism over the electric motor system used by all other teams. In trying to explain the nose cone, the text and an illustration show a high nose and low nose configuration, but does not remark why one is beneficial over the other.
This section also covers very brief summaries of bargeboards, sidepods and the floor. Some nice close up photos of these parts included, but again with little explanation. An illustration at this point highlights the other FIA deflection test altered in 2010, which was aimed at Red Bulls alleged flexing T-Tray splitter. In this section the text cites Ferraris sprung floor of 2007, but not the allegation that RBR’s was flexing in 2010. A further simple graphic illustrates the venturi effect of the floor and diffuser, and then the text goes into simple explanations of both the double diffuser and the exhaust blown diffuser.
Having been one of the technical innovations of 2010 and since banned, the book is able to cover the F-Duct is some detail. A complete CAD render of the ducting is provided on page 53; this shows an additional inlet to the drivers control duct that was never visible on the car. This extra duct served the same function as the nose mounted scoop on the McLaren that introduced the F-Duct to F1.
Thus with aerodynamics covered in some 23 pages, the text moves onto suspension and the expectation of detail on the RB5-6’s trademark pullrod rear suspension. After a summary of the purpose of an F1 cars suspension, Pages 58-59 have some fantastic CAD renderings of front suspension, uprights and hub layouts. However the rear suspension rendering stops short at the pull rod and no rocker, spring, damper layouts are detailed. Hardly a secret item, so lacking this detail is let down for a book announced as an RB6 workshop manual. A lesser point, but also highlighting the censorship of some fairly key technical designs, was the lack of any reference to Inerters (Inertia or J-Dampers), The suspension rendering simply pointing to the inerter and calls it the ‘heave spring’, while naming the actual heave spring damper as simply another ‘damper’. Inerters have been in F1 since 2006, predating Renault’s mass damper. Their design and purpose is well documented and shouldn’t be considered something that needs censoring. It’s also this section that fails to showcase the RB5-6 gearbox case. Instead using a pushrod suspended RB4 (2008) gearbox, albeit one made in carbon fibre.
The steering column, rack and track rods are similarly illustrated with CAD images. This usefully shows the articulation in the column, but little of the hydraulic power assistance mechanism. Page 67 starts the section on brakes, again fantastic CAD images supply the visual reference for the upright, brake caliper and brake duct design. As well as a schematic of the brake pedal, master cylinder and brake line layout of the entire car. A nod to more typical Haynes manuals shows the removal of the brake caliper and measure of the Carbon discpad. A further CAD image shows the brake bias arrangement with both the pivot at the pedal and the ratchet control in the cockpit for the driver to alter bias.
Although not a RBR component the Renault engine is covered in the next Chapter. An overview of the complex engine rules regarding the design and the specification freeze kicks off this section and cites the tolerances and compression ratio for a typical F1 engine. Pneumatic valves, for along time an F1-only technology are explained, but even I failed to understand the schematic illustrating these on page 77. Also covered in the engine section is some more detail on the fuel, oil and cooling systems. With useful specifics, like capacity of the oil system at 4 litres and water coolant at 8 litres. Again some nice CAD images illustrate the radiators within the sidepod. Many sections have a yellow highlighted feature column; this sections feature is on the engine start up procedure, one of the mundane, but rarely talked about processes around an F1 car (other features are on the shark fin and brake wear). As KERS wasn’t used up until 2011, this topic is skipped through with a just a short explanation of the system.
Moving rearward to the transmission system, the old RB4 gearbox makes a reappearance. Again this disappoints, as some quite common F1 technology does not get covered. Page88 shows some close up photos of a gear cluster, but this is not a seamless shift gearbox. In fact seamless shift isn’t mentioned, even though it made its RBR debut in 2008, the year of the gearbox showcased in the book. I know many will highlight that this might be a secret technology. But most teams sport a dual gear selector barrel, each selector looking after alternate gears to provide the rapid shift required to be competitive in F1. So I think this is another technology that could be explained but hasn’t been.
Tyres, Wheel and Wheel nuts get a short section, before the text moves onto electronics. A large part of the electronic system on a current F1 car is now standardised by the Single ECU (SECU) and the peripherals that are designed to support it. So this section is unusually detailed in pointing out the hardware and where it’s fitted to the car. From the tiny battery to the critical SECU itself. Other electronic systems are briefly described from the Radio, drivers drink system to the rain light.
Of critical importance to the modern F1 car are hydraulics, which are detailed on p105. As with the other sections, CAD images and some photos of the items themselves explain the hydraulic system, although there isn’t a complete overview of how it all fits together.
Rounding off the anatomy chapter is the section of safety items and the cockpit. The steering wheel and pedals are well illustrated with CAD drawings and keys to the buttons on the wheel itself and on the switch panel inside the cockpit.
While I have pointed that the hardware shown in the anatomy chapter isn’t necessarily of the RB6, what is on show is obviously genuine and recent RBR. So for those not so familiar with the cars constituent parts, there isn’t a better source of this available in print today. Even web resources will fail to have such a comprehensive breakdown of an F1 car.
The Designers view
Moving away from the Haynes format of a workshop manual, the book then moves into a chapter on the cars design, with comments from Adrian Newey. It details the Design Team structure and some of the key individuals are listed. The text then covers the key design parameters; centre of the gravity and the centre of pressure (downforce). Plus the design solutions used to understand them; CFD, Wind Tunnels and other simulation techniques. Each being briefly covered, before similar short sections on testing and development close this chapter.
Although the text makes reference to creating ‘the package’, something Newey excels at. This section doesn’t provide the insight into the overall design philosophy, which one might have hoped for.
The Race Engineers view
Where as the Designers view chapter was limited, the race Engineers section was a little more insightful into the rarely talked about discipline of getting the car to perform on track. The process of setting up the car is covered; from the understanding of the data, to the set up variables that the race engineer can tune; suspension, aero, ballast, gearing brakes and even engine. Usefully the grand prix weekend is broken down onto the key events from scrutineering, to running the car and the post race debrief. Feature columns in this chapter include; Vettels pre race preparation and the countdown to the race start.
The Drivers view
Ending the book is an interview style chapter on the driver’s time in the car, mainly the driver’s perspective from within the cockpit when driving the car on the limit and the mindset for a qualifying lap. A simplistic telemetry trace of a lap around Silverstone is illustrated, although there is little written to explain the traces (brakes, speed and gear), this is accompanied by Mark Webbers breakdown of a lap around the new Silverstone circuit.
When I first got this book, I was constantly asked if it was worth the purchase or if I’d recommend it. If my review is critical at points, it’s mainly because some technology that could have been covered wasn’t. Or, that the content falls short of the books title suggesting it was a manual for the RB6.
Those points aside, I have learnt things from this book. Like details of the F-duct system, the Front Flap Adjuster and a wealth of smaller facts. There isn’t a better book on the contemporary F1 car. In particular the CAD drawings and close-up photos, just simply aren’t in the public domain. From the pictures we got over the race weekends, we never get to see half the hardware and design work that’s pictured in this book. So I’ll keep this book on hand for reference for several seasons to come.
Overall I’d recommend this book to anyone with a technical interest in F1.
Many thanks to Haynes Publishing who have allowed me to use their Images and PDFs to illustrate this article
This book is available from Haynes
Having run KERS for Friday only in Melbourne, RBR will probably run the KERS system for the full weekend in Sepang. As RBR were not seen to use KERS on their qualifying laps, although they were unknown to be equipped with Renaults KERS raised rumours of a start only KERS. While a start only KERS is technically legal and has some technical advantages, it’s not thought such a system is planned for any team.
From images seen this in the team’s garage this morning we can see the KERS set up quite clearly. The actual set up is quite different to the image provided by Red bull in their Launch press pack. Which shows a far more conventional layout?
On the right hand side of the car, we can see a silver box with FIA anti-tamper seals; this is the KERS control unit (KCU). This controls the power exchange between the motor generator and the battery pack. The thick red cables carry the current in between these other devices. Running very hot from the current passing through it, the KCU will have a cool air feed from the sidepod ducting. Although not certain, the small radiator at the bottom of the other coolers is probably to cool the battery pack.
From the other side we can see the Battery pack, unusually this is mounted to the side of the gearbox. It is the rounded carbon fibre item, with the yellow warning sticker.
The other three KERS suppliers (Mercedes, Ferrari and Williams) all place this item beneath the fuel tank for better weight distribution and crash safety. Although McLaren did place theirs low down in the front of the sidepod in 2009. With the more rear biased mandatory weight distribution rule, this more rearwards location is not a handicap. It frees up fuel capacity and sits inside a dead area of space within the sidepod. You can see the same thick red cable emerging from the battery pack. Inside the carbon case will be an array of small lithium-Ion cells (Li-ion). These will run at high temperatures as the cells charge and discharge, as explained they will be cooled a dedicated water radiator and pump.
More on KERS: http://scarbsf1.wordpress.com/2010/10/20/kers-anatomy/
It seems recently more rumours and speculation circulate around the Hispania Racing Team than around any other team. But the first sign that the team will remain in F1 for 2011, was the announcement that they will be provided with gearboxes from Williams F1 from next season.
In their debut year Hispania (HRT) have run the standard Xtrac gearbox and hydraulics, being mated to the Cosworth engine and in turn to a Dallara chassis. This standard FIA specification rear end has been supplied to all three of the new teams (albeit with Virgin running their own gear case). The set up has not been without its own issues. Largely related to the reliability of the hydraulics package that controls various parts of the transmission. Having been the weak point on an F1 car for many years, for the existing teams at least the hydraulic system has finally matured into a reliable system. So it’s no slur on Xtrac that their first contemporary hydraulics package is less reliable than a seasoned F1 teams set up. To take step forward for 2011 and improve reliability the new teams have been seeking an alternative supply of gearbox and transmission technology. With Williams also running the Cosworth engine, their gearbox and ancillaries are already matched to the same engine as the new teams and reliable with it. So it’s no surprise that Williams have been offering this proprietary technology to other teams.
The short press release provided few details, but Williams have provided me with more information on the technical deal. Announced as a deal for Williams to provide HRT with transmission systems from 2011. The release added that this deal will extend for the life of the current Cosworth engine deal, expected to change with the new engine rules for 2013. This of course underlines the fact that Hispania will continue to use the Cosworth the CA2010 V8 beyond this year.
Williams have a record in sharing gearbox technology, the team provided Toyota with seamless gearbox technology while the pair shared a common engine supply in 2007. Williams had already run a seamless shift of their own in 2006, but this double clutch set up was discarded for their second generation set up. This latter version was shared with Toyota and exploited the now common method of using a double selector mechanism to provide the seamless shift.
What Williams will be providing HRT is a complete rear end package; this will be the complete gearbox including gear case. Williams have run a cast aluminium case for many years, although they have investigated carbon and titanium cases over the years, they feel the Alu case is the best solution for them. When asked if the deal was to provide the same specification as the Williams teams will use, as opposed to a bespoke case, Williams would only say that specific detail was “confidential”. With HRT’s limited budget and lack of technical resources, it would be expected for the team to share a common casing, perhaps with only the detail machining varying between the two teams.
In addition to the gearbox and case, Williams are also supplying HRT with “all associated hydraulics”. Perhaps this is the most critical aspect of the deal, while gearbox technology is not quite a commodity item, it is relatively accessible. However the hydraulics package is harder to acquire and takes time to develop. The systems are not commonly used in other motor sport formulae and differ in detail from Aerospace systems. It was after all Williams that matured modern electro hydraulic controls with their active suspension and winning world championships with them in the nineties. Albeit, it was the pioneering work done by Lotus that introduced the systems into F1 in the eighties.
KERS will be part of F1 again next year, again Williams via its subsidiary Williams Hybrid Power, has proprietary technology available to other teams. However Williams confirmed that there was “no KERS solution under this agreement”. This leaves Hispania to seek a KERS solution from Cosworth or another vendor.
Effectively Williams will provide the entire assembly from the rear face of the engine to the start of the rear crash structure. Primarily this will lead HRT to have the same rear suspension set up as Williams. For 2010 Williams have focussed on packaging their pushrod suspension to create as lower line shape the Red Bulls much talked about Pull Rod set up. Having a push rod set up necessitates having the rockers, torsions bars, dampers and antiroll bars on top of the gear case. With a double diffuser, pushrod creates more space for the diffuser at the cost of a streamlined shape to the cowling leading the lower beam wing. Next year with double diffusers banned, the Pullrod set up may be more beneficial, having less impact on diffuser packaging and better flow to the rear wing. Sam Michael confirmed to me at the FW32’s launch, that a pull rod set up was assessed for 2010, but the concept was discarded. But it’s possible the Pullrod solution could be back on the specification for 2011. Thus HRT will run the Williams inboard suspension geometry leaving the designers to adapt their rear suspension around those constraints and in turn the front suspension to match that.
With the majority of the rear end specified, it remains for HRT to design the rest of the car. The 2010 car was designed by Dallara, but the relationship fell apart after the opening races. Acting as a consultant, Geoff Willis was critical of the Dallara project and HRT have since severed ties with the Italian constructor. Rumours link the HRT team to Toyota, largely as the defunct Toyota motor sport team have F1 designs available for sale. Added to the fact that the base for the otherwise Spanish branded team is based in Germany at Colin Kolles workshops in Greding, some 4 hours drive from Toyota in Cologne. Rumours that the team had bought the entire Toyota operation for some $50m have been rubbished. It’s still possible that the car could be designed using existing Toyota IP or from new by their in-house design team. It’s also possible that a design office lead by Willis using German based design talent, could be a route to designing the car. This approach was taken by Lotus to get their 2010 car up and running.
Hopefully any design programme is already well under way, as the car will otherwise be very late. HRT will need an aero concept, suspension, electronics and the primary structures (i.e. monocoque & crash structures). The lead times for these programmes in both design and manufacturing terms are very long and with the season nearly complete, there’s just four months until testing commences in February. HRT have not confirmed any details of their chassis programme for 2011. So despite the deal announced today it’s far from clear if they can make it to grid next year.