Trends 2011 – Exhausts and Diffusers

This year the technical talk has largely been about exhausts.  How teams have adapted to the ban on double diffusers and the added restriction on Exhaust blown diffusers. Just to aid understanding going into the new season, I have explained how these solutions work and how they look from beneath.

Double Diffusers

Force India 2010 Double Deck Diffuser (DDD)

Since 2009 the regulations regarding the floor have been interpreted in a literal sense to allow the double deck diffuser (DDD). Indeed the very same rules were exploited to a lesser extent under the previous rules, but this only produced small extra channels in between the outer and middle diffuser tunnels. With the major cut in aerodynamic aids for 2009, several teams sought to find a way to gain more expansion ratio from the smaller diffusers. In essence the loophole exploited the definition of surfaces formed between the step and reference planes. Multiple surfaces allowed fully enclosed holes, which fed the upper diffuser deck that sat above the 175mm lower diffuser. This allowed diffuser to be significantly larger in order to create more downforce. Notably Brawn, Williams and Toyota launched 2009 cars with DDDs. Other teams soon followed suit in 2009 and last year every car exploited the same loophole. Over the winter the FIA acted to close the loophole, by enforcing a single continuous surface across a 90cm span under the floor. In a stroke this banned the double diffuser, there being no scope to create any openings in the floor to feed the upper deck.

Single Diffuser

Double Diffuser

 

Exhaust Blown Diffusers
Another approach to regain lost downforce was the re-invention in 2010 of the exhaust blown diffuser (EBD). This used high energy exhaust gasses to blow the diffuser, the faster throughput of flow under the floor increased downforce. Two methods of EBDs were used in 2010, one blowing over the diffuser and the second blowing inside the diffuser. This latter solution was more effective at driving flow through the diffuser and created more downforce. However this necessitated a hole made into the diffuser to allow the exhaust gas to enter, I‘ve termed this method an ‘open fronted diffuser‘.

2011: No openings allowed in the yellow 90cm zone, outside certain holes are permitted

A by product of the 2011 rules intended to ban the DDD, also stopped this open fronted diffuser solution. However the rules enforced the continuous surface only across a 90cm width of floor and the diffuser is allowed to be 100cm wide. Thus a 5cm window was allowed each side of the diffuser.

Outer Blown Diffuser – Solution

Red Bull Diffuser: Flow passes under the outer 5cm of floor into the diffuser

Red Bull and Ferrari appear to have found this loophole simultaneously. Recently Sam Michael pointed out this was probably the most efficient way to blow the diffuser under the new rules. As Red Bull appeared with this set up first, its often termed the Red Bull Blown diffuser.

What these teams have done is to open up the floor 5cm either side of the diffuser, then route the exhaust towards this opening. The exhaust gas gets collected by the coved section of floor and this directs the high energy gasses under the diffuser, to recover some of the losses from the more open diffuser allowed last year.

Front Exit Exhaust

Renault Front Exit Exhaust: Flow passes wide around the floor before entering the diffuser

Renault meanwhile turned the problem on its head. As the aim of the EBD is to increase flow under the car, they pointed their exhaust at the front of the floor. I’ve had it confirmed to me by two ex-Renault sources that the exhaust does indeed mainly flow under the floor.

The exhaust pipe outlet sits above the step plane just ahead of the leading edge of the floor. This is not simply blowing out horizontally and across the floor, but is ducted slightly to blow downwards and backwards, this is roughly in line the with the flow trailing off the “V” shape above the splitter. Along with the strong vortices set up by the splitter, vanes and bargeboards, this makes the floor appear wider than it is. The flow will go out beyond the floor and then curl back in and under the floor. Some flow will inevitably pass over the floor, but the most of the energy will be driving more flow under the floor to the diffuser.

McLarens Slit Exhaust

The slit above the floor is visible. Copyright: Liubomir Asenov

No conversation about exhausts this year, would be complete without some speculation about McLaren. Amongst the several exhaust systems run by McLaren over the pre-season tests was a “slit” exhaust. This appeared at the first Barcelona test, but did not seem to appear for the second Cataluña test. The exhaust collector could be seen to duct towards a double thickness section of floor ahead of the rear wheels. This section was also interesting for its longitudinal slot, this slot was not large enough to be the actual exhaust outlet, This might be a cooling slot, or to improve the flow from above to beneath the floor.  I beleive the Exhaust is actually below the floor.  As when the car ran the same floor with a conventional exhaust outlet, there appeared to be a removable section of floor ahead of the rear wheels. Being just outside of the 90mm opening rule, the floor ‘could’ be opened to allow an exhaust to blow through to underneath. If sculpted correctly, the exhaust could be ducted back inboard and blow towards the diffuser from under the floor. It’s possible that this could be in interpretation of a legal opening, assuming it met the maximum fillet radius rules.
I’d expect the resulting exhaust outlets to be a long wide slot, this wider outlet would be needed to meet the maximum radius rules and also reduce the back pressure from the tight curve of the exhaust outlet. As the exhaust would have a tortuous bend, to curl back under itself to direct the flow inboard, rather than out wide around the rear tyre.

Mac Slit: The exhaust might exit beneath the floor in a long narrow outlet

Follow ScarbsF1 on Twitter

Leave a Reply

Your email address will not be published. Required fields are marked *

You may use these HTML tags and attributes: <a href="" title=""> <abbr title=""> <acronym title=""> <b> <blockquote cite=""> <cite> <code> <del datetime=""> <em> <i> <q cite=""> <strike> <strong>